AH2 / AH2 Max Hydraulic Autosteering
Hydraulic steering control without replacing your steering wheel
The FJDynamics (FJD) Hydraulic Autosteering Kit uses your tractor’s hydraulic system to provide automated steering while keeping the original steering wheel in place. It delivers 2.5 cm steering accuracy and supports guidance lines, automatic U-turns, and operation across rolling ground, slopes, and rough terrain.
Best for: Farmers who need stable, precise steering on high-horsepower tractors and challenging terrain.
For sale and in stock. Ships to the farm anywhere in the US, set up with you on the phone. Two-year warranty. Ask for a quote or call or text (580) 394-0089.
Talk To Farm Experts Call or Text (580) 394-0089What the FJD Hydraulic Autosteering Kit does for you
Keep Your Steering Wheel
The kit integrates with the tractor’s original steering wheel. No steering wheel replacement is required.
Precise Hydraulic Control
Hydraulic oil regulation provides automated steering control with 2.5 cm steering accuracy.
Built For Tough Terrain
The system is designed to maintain steering stability on rolling terrain, slopes, and rough ground.
Automatic U-Turns
Smart U-turn plans paths for headlands and row ends. Basic U-turn provides Ω and fishtail turnaround shapes.
Wide Tractor Compatibility
Four compact hydraulic valve options support different fluid types and both open-center and closed-center hydraulic systems. We match the valve to your tractor, high-horsepower machines included.
Connects With FMS
The kit can synchronize with a Farm Management System for planned tasks such as setting boundary lines and guidance paths.
Which tractors does the FJD Hydraulic Autosteering Kit go on?
Pick your tractor brand for the model-by-model fit, or send us the make, model and year.
The AH2 and AH2 Max up close
Both versions steer through a hydraulic valve, so your steering wheel stays where it is. Deep Sand Technology is an authorized FJDynamics dealer. We sell, set up and support the FJD AH2 and AH2 Max for farms in all 50 states.







Tap any picture to see it full size.
What comes in the AH2 or AH2 Max kit
Both versions use a cab display and one roof receiver. The wiring and valve parts are matched to your tractor.

Cab touchscreen
Shows guidance and controls steering. AH2 has a 10.1-inch screen; AH2 Max has a 12.1-inch screen.

Tractor-side valve wiring
Connects the display's hydraulic controls to the valve. The cable and plugs depend on the tractor and valve.
If the tractor has a compatible steering valve, the kit can connect to it directly. A retrofit without a usable valve adds a matched hydraulic valve, with hoses and fittings sized to the tractor. Wheel-angle feedback, a manual-override pressure sensor or factory flow switch, and a separate changeover valve or lead depend on the setup.
Every kit we ship also comes with RTK activation, a SIM card with a one-year data plan and setup help by phone. Options: engage switch, remote, camera and ISOBUS hardware. The AH2 steers through the valve, so your factory steering wheel stays.
We offer both radio and NTRIP RTK. Every system ships set up on NTRIP RTK.
Video: AH2 in 30 seconds
The FJD AH2 is a hydraulic auto steer system for tractors. It steers through a hydraulic valve, so you keep your factory steering wheel.
What the video shows
- Steers through a hydraulic valve
- Keeps your factory steering wheel
- Pick your screen: 10-inch, 12-inch Max or 16-inch Ultra
- 1-inch accuracy
- Terrain compensation
- Auto turn available
- ISOBUS implement control
- Section and rate control
- Two-year warranty
- One-year buy-back guarantee
How does the AH2 steer the tractor?
Through a hydraulic valve, so your factory steering wheel stays in place.
Which screen does the AH2 use?
Your choice of the 10-inch display, the 12-inch Max or the 16-inch Ultra.
Hydraulic auto steer system or a motor on the wheel?
FJD steers a tractor two ways. The AT2 family puts an electric motor on the steering column and turns the wheel. The AH2 is a hydraulic auto steer system: it runs the tractor's steering valve directly, with a pressure sensor and a wheel angle sensor telling the controller what the front wheels are doing. Both hold the same RTK line. The question is which one belongs on your tractor.
Where we put the AH2
- Tractors that already have a guidance valve but no CAN steering. Guidance-ready Magnums, Pumas and Maxxums from before CAN carry an Eaton valve, and guidance-ready Steigers and STX tractors drive theirs with a voltage signal, not CAN. The AH2 runs that valve. On Steigers it takes a new valve head and two plug changes.
- Farmers who want the steering wheel left untouched. Nothing is bolted to the column, the wheel stays exactly as it was, and the valve holds the line. That goes for a Magnum as much as a 9230 Steiger, which has run on the AH2 lock to lock once the angle sensor was set right. See autosteer for articulated 4WDs.
- Tractors with no valve at all where the owner wants hydraulic steering anyway. Any tractor with power steering can have a steering valve added, and the big 4WDs have the pump capacity for it. Most of those farmers run the motor kit instead, because it is simpler and it moves to another tractor, and that is fine too.
Where the motor kit is the better answer
Any tractor with power steering and no factory autosteer. The AT2 Lite, AT2, AT2 Max and AT2 Ultra bolt to the column with a model-specific bracket, and most farmers install one in an afternoon with our tech on the phone. That is the kit on most of the older tractors we steer.
And if the tractor is steer-ready with CAN
Then neither. The AS2 plugs into the factory connector. Is my tractor steer-ready? shows how to tell in ten minutes. If you would rather not guess, text us the model and serial number at (580) 394-0089 and we will tell you which of the three it is.
AH2 and AH2 Max specifications
Display
| AH2 | 10.1-inch touchscreen |
|---|---|
| AH2 Max | 12.1-inch touchscreen with split screen |
| AH2 case | 10.83 x 7.09 x 1.57 in (275 x 180 x 40 mm) |
Receiver and accuracy
| Accuracy | About 1 in (2.5 cm) with RTK |
|---|---|
| Receiver size | 6.38 x 2.54 in (162 x 64.5 mm) |
| Satellite bands | GPS L1 C/A, L1C, L2P(W), L2C, L5; GLONASS L1/L2; BeiDou B1I/B2I/B3I/B1C/B2a; Galileo E1/E5a/E5b; QZSS L1/L2/L5 |
| RTK setup | Ships set up on NTRIP RTK; radio RTK also offered |
Hydraulic valve
| Valve fit | Reuse a compatible valve or add a matched valve |
|---|---|
| Retrofit flow | 7.9 or 15.9 US gal/min (30 or 60 L/min) |
| Retrofit types | Open-center or closed-center, depending on tractor |
Sensors
| Pressure sensor range | 3,000 psi (207 bar) |
|---|---|
| Pressure sensor output | 0-5 V DC; G 1/4 external thread |
| Angle sensor temperature | -40 to 185 deg F (-40 to 85 deg C) |
Power
| AH2 terminal | 9-36 V DC |
|---|---|
| Retrofit valve | 12 V |
Weather and temperature
| AH2 terminal | IP65 |
|---|---|
| GNSS receiver | IP66 |
| Angle sensor | IP67 |
Connections
| Valve connection | Machine-specific hydraulic wiring |
|---|---|
| AH2 cellular hardware | 4G, 3G and 2G; service varies by carrier |
Software
| Guidance | Guidance lines and terrain compensation |
|---|---|
| Headland turns | Basic and Smart U-turn options; ask us about activation |
Rows marked AH2 terminal are for the 10.1-inch AH2 screen, not the AH2 Max screen. Ask us if you want the AH2 Max numbers.
Which hydraulic setup fits your tractor?
| Compatible valve already fitted | New-valve retrofit | |
|---|---|---|
| Steering valve | Reuse the compatible valve | Add a matched hydraulic valve |
| Wiring | Matched to the existing valve | Matched to the added valve |
| Feedback | Use compatible factory feedback or add sensors as needed | Match wheel angle and manual override sensing to the retrofit |
The tractor decides the setup, not the screen size. Tell us your tractor and we will tell you which one it takes.
At a glance
| AH2 display | 10.1 in |
|---|---|
| AH2 Max display | 12.1 in |
| Steering wheel | Keeps the factory wheel |
| Valve | Reuse a compatible valve or add one |
| Accuracy | About 1 in (2.5 cm) with RTK |
| Retrofit choices | Open-center or closed-center |
Compatibility
The kit is intended for a wide range of tractors, including high-horsepower models, and supports open-center and closed-center hydraulic systems through multiple valve options. Call Deep Sand Technology to confirm the correct valve and installation approach for your tractor; remote install support is available.
Not sure it fits your equipment? Send us the make, model and year and we will tell you straight.
Common questions
Will I have to remove my tractor’s steering wheel?
No. The kit is designed to work with the tractor’s original steering wheel.
Can it work with my tractor’s hydraulic system?
The system supports open-center and closed-center hydraulic systems and different fluid types. Tell us your make and model and we will match the right valve to your tractor.
What does the kit include for automatic turns?
It supports Smart U-turn and Basic U-turn functions. Smart U-turn plans a path for headlands, while Basic U-turn offers Ω and fishtail turnaround shapes.
More in Autosteering & Guidance
AT2 Ultra Autosteering System
Keep your eyes on the job, with voice-assisted precision steering.
Learn moreAT2 Max Autosteering System
More screen and control for precision tractor guidance.
Learn moreAT2 Autosteering System
Keep the tractor on line and reduce skips, overlaps, and operator fatigue.
Learn moreAT2 Lite Autosteering System
RTK steering guidance for a simpler start in precision farming
Learn moreFarmers helping farmers
Over 30 years of experience. Trusted by thousands of farmers across the US. Two-year warranty. One-year buy-back guarantee. US-based support out of Oklahoma.
More on auto steer
Auto steer for tractors · How auto steer works · Is my tractor steer-ready? · Auto steer for older tractors · AS2 steer-ready · Compare FJD auto steer systems · Tractor GPS systems · RTK vs WAAS · FJD AT2 vs Wheelman · FJD AT2 vs Trimble EZ-Steer · All buyer guides · Autosteer solutions across the United States





