Auto Steer for Fendt and Challenger Tractors

Serving the United States

Created by Farmers for Farmers

Buy-Back Guarantee

Two-Year Warranty

Precision Products for New and Older Equipment

Vario, MT tracks, Rogator, any year
Vario, MT tracks, Rogator, any year

Autosteer for Tractors

We sell, ship and support auto steer in every state. This page is about Fendt and Challenger tractors. Different brand? The Autosteer for Tractors page covers them all, or just call us.

Auto steer for Fendt and Challenger tractors, any model, any year

Deep Sand Tech puts affordable FJDynamics auto steer on Fendt and Challenger iron of every age, from a 2001 Fendt 926 to a FendtONE 1050 Vario to a Challenger MT765 on tracks, steer ready or not. If it has a steering wheel and power steering, Deep Sand Tech has you covered! Every system comes with sub-inch RTK accuracy unlocked, a two-year warranty, fast phone and remote-login support, and a 1-year buy back guarantee.

Get a quote for your Fendt Call or Text (580) 394-0089
Any Fendt or ChallengerVario 200 to 1000, MT wheeled, MT tracks, MT900 articulated, Rogator, Spra-Coupe
Plug-in CAN steerGuidance-ready Fendt 300 to 1000 Vario are on FJD’s approved CAN list
Within 1 inchRTK pass-to-pass accuracy on the same lines year after year
1-year buy backRun it a season. If it is not for you, we buy it back

Three ways we steer a Fendt or a Challenger

  1. AS2 on the factory CAN plug

    AGCO put CAN steering on more tractors, earlier, than anyone else. Guidance-ready Fendt 300, 500, 700, 800, 900 and 1000 Vario from 2011 on, and guidance-ready Challenger MT wheeled and track tractors, steer over CAN. AS2 plugs into the ISO port under the console with no motor on the column. We confirm the serial before it ships.

  2. Electric motor kit on the column

    AT2 Lite, AT2, AT2 Max or AT2 Ultra. A motor and a model-specific bracket bolt to the steering column and turn the wheel. Fits any Fendt or Challenger with a steering wheel. This is what goes on pre-2010 Fendt Varios, base-model Challengers, Spra-Coupes and the Challenger swathers. Most farmers install it themselves in an afternoon.

  3. AH2 hydraulic kit

    Guidance-ready Fendt 700, 800 and 900 Varios from 2007 to 2010 carry a hydraulic steering valve, not CAN, and some Challenger owners want a valve instead of a motor. AH2 runs the valve that is there or one we add. Challenger PVED valves are the CL type in our software. If CL does not take, we switch to CC. No harm done.


Fendt and Challenger model families and what fits

What each family came with from the factory, and what we usually put on it. A family being listed means the option existed, not that every tractor has it, so we confirm on your unit before anything ships.

Model familyFrom the factoryWhat we usually install
Fendt 900 Vario, 2006 and older
916, 920, 924, 926, 930
No steering valve. Power steering only. Too old for CAN steer.Electric motor kit. A 926 takes a number 13 spline, which we have had custom made.
Fendt 700, 800 and 900 Vario, 2007 to 2010
712 to 718, 818, 820, 922 to 936
Base models have no valve. Guidance-ready units of these years carry a factory hydraulic valve, not CAN.Motor kit on base models. On a guidance-ready unit we check the valve and run the AH2 on it, or go with the motor kit.
Fendt 300, 500, 700, 800 and 900 Vario, 2011 and newer
311 to 314, 512 to 516, 714 to 724, 822 to 828, 930 to 942
CAN steering on guidance-ready units. On FJD’s approved list.AS2 plugs into the ISO port. We ship our own angle sensor because the factory one is not linear on curves. Motor kit on base models.
Fendt 1000 Vario and FendtONE models
1038 to 1050, 600 Vario 614 to 620, 200 Vario 209 to 211
CAN steering on guidance-ready units. The 1000 Vario is on FJD’s approved list.AS2. We confirm the FendtONE 600 and 200 Varios by serial before anything ships.
Fendt 900 MT and 1100 MT tracks
938MT to 943MT, 1149MT to 1167MT
Guidance-ready units steer over CAN.AS2, scoped with you before it ships. Track tractors are an involved install and we walk you through it.
Challenger MT 400 and MT 500 wheeled
MT425B to MT495D, MT515D to MT595B
Base models have no valve. Guidance-ready units steer over CAN with a PVED CL valve.AS2 on guidance-ready units, motor kit on base models.
Challenger MT 600 wheeled
MT635B to MT685E
Base models have no valve. Guidance-ready units steer over CAN.AS2 on guidance-ready units. Motor kit on base models. An MT635B takes the H bracket and the number 14 spline.
Challenger MT 700 and MT 800 tracks
MT735B to MT775E, MT835B to MT875E
Guidance-ready units steer over CAN. B series needs a wheel angle sensor and a converter.C, D and E series: AS2, scoped with you before it ships. B series: motor kit.
Challenger MT 900 articulated
MT945B to MT975E
Base models have no valve. Guidance-ready C and E series steer over CAN.Motor kit in articulated mode on base models. AS2 on guidance-ready C and E units.
Rogator and Spra-Coupe
RG932 to RG937H, 4455 to 4660
Guidance-ready Rogator 900 steers over CAN. Spra-Coupes have no valve.Rogator: AS2 or motor kit. Spra-Coupe: the cab is tight, so the AH2 with a valve is the clean install. The motor kit fits with the number 6 bracket on the trimmed column.
Challenger WR swathers
WR9740 to WR9870
Guidance-ready from the factory. FJD is still working on CAN support for AGCO swathers.Electric motor kit with the number 4 spline and the number 4 or 6 bracket.

Not on the list, or a different brand wearing the same model number? Call us. We have put kits on 2001 Fendt 926s and on Challenger MT635Bs.


See the AS2 steer-ready kit

What a plug-in install looks like on a steer-ready tractor. One minute and forty-three seconds.

Deep Sand Technology Now Offers The AS2 Steer Ready Autosteering System

What goes on the tractor

FJD AT2 electric steering motor mounted on a tractor steering column
The motor bolts to the steering column and turns the wheel. Nothing in the hydraulics is touched.
FJD GNSS receiver mounted on a tractor roof
The GNSS receiver goes on the roof and takes the RTK correction over cellular or radio.

Things we have learned on Fendt installs

  • On Fendts the factory angle sensor is not linear, so curves come out better on the FJD angle sensor. We ship it with the kit.
  • A Fendt 926 from 2001 or 2002 is too old to be CAN steer. It takes a number 13 spline, which we have had custom made.
  • On a Fendt or Challenger there are two ports under the console, EDT for diagnostics and ISO for steering. The cable goes in the ISO port. If you plug into EDT you get a transmission error that has nothing to do with the transmission.
  • AGCO steer-ready power cables come wired to the European standard. We swap the pins on the three-prong plug to the American standard before it ships.
  • Challenger PVED valves are the CL type, not CC. CL and CC are valve types, not closed center. If CL does not work, switching to CC does no harm.
  • A Fendt 922 with the in-cab 9-pin ISOBUS connector takes FJD’s in-cab ISO harness to that 9-pin for its Krone mower and Massey baler. Steering and ISOBUS on one screen.
  • A Spra-Coupe cab has less room than a small car. The AT2 Max display does not fit comfortably, so we go AH2 with a valve, or run extra cable and mount the display where it fits.
  • Tracked Challengers are the most involved AGCO install we do. We scope the valve type, the CAN cable and the angle sensor with you before anything ships, not after.
What to send us for a quote
  • Model and year, and the serial number if you can read it.
  • A photo of the steering column from the seat, so we match the bracket and spline.
  • A photo of the ports under the right-hand console, and whether the display has a steering screen.
  • Any implement you want rate or section control on, and which display is already in the cab.
Talk to farm experts

Common questions from Fendt owners

Will auto steer work on a Fendt?

Yes. Guidance-ready Fendt 300 through 1000 Vario tractors from 2011 on take the AS2 on the CAN plug. Guidance-ready 2007 to 2010 units carry a hydraulic valve and take the AH2. Older Fendts like a 926 run the motor kit with a custom spline.

My Fendt is guidance-ready from the factory. Is it plug and play?

On a 2011 or newer Vario, yes. The AS2 plugs into the ISO port under the console. We swap the power-cable pins to the American standard and ship our own angle sensor, because the factory one is not linear on curves. We confirm the serial first.

What about my Challenger tracks?

MT700 and MT800 C, D and E series steer over CAN and take the AS2. These are involved installs and we scope them with you before anything ships. B series tracks run the motor kit.

Can it steer a Challenger MT900 articulated?

Yes. Base models run the motor kit in articulated mode. Guidance-ready C and E series steer over CAN and take the AS2. Articulated tractors have their own settings, and we walk you through them on the phone.

Will it run my Fendt or Challenger implements?

Steering, yes. Rate and section control depends on the implement. A Fendt 922 with the in-cab 9-pin takes FJD’s ISO harness for a Krone mower and a Massey baler. Send us the controller model and we tell you.

Do I need my own base station?

Usually not. Every kit ships with an RTK plan, and most customers run on the GEODNET network, which needs no base station of your own. Where coverage is thin we set you up with a base station or StarNav. We check coverage at your farm before we quote.

Who installs it and who do I call?

Most farmers install the motor kit themselves in an afternoon with our tech on the phone. Steer-ready installs take longer and we walk you through them. After that you call or text Deep Sand Tech, and we can log into the display remotely to help.


Other tractor brands

Same approach, different color of paint. Pick a brand for its model-by-model fit.

More on auto steer

Auto steer for tractors · How auto steer works · Is my tractor steer-ready? · Autosteer for older tractors · Hydraulic auto steer (AH2) · AS2 steer-ready · All autosteer kits · RTK vs WAAS · FJD AT2 vs Wheelman · All buyer guides · Autosteer solutions across the United States

Deep Sand Technology

About Deep Sand Technology

Deep Sand Technology (Deep Sand Tech) is a farmer-owned, authorized FJDynamics dealer with over 30 years of experience. We sell, ship, install and support FJD autosteer kits and GEODNET network RTK for thousands of farmers across the US, in all 50 states. Everything on this page comes from our own installs and support calls, not from a brochure.

About us · Farmer reviews · Talk to a farmer · Call or text (580) 394-0089

It's easy to get started. Talk to a farmer today.

By submitting this form you agree to our Privacy Policy.