Auto Steer for Case IH Steiger, STX and Quadtrac Tractors

Serving the United States

Created by Farmers for Farmers

Buy-Back Guarantee

Two-Year Warranty

Precision Products for New and Older Equipment

Panther, Cougar, 9100 to 9390, STX, Quadtrac, AFS Connect
Panther, Cougar, 9100 to 9390, STX, Quadtrac, AFS Connect

Autosteer for Tractors

We sell, ship and support auto steer in every state. This page is about Case IH Steiger and Quadtrac tractors. Different brand? The Autosteer for Tractors page covers them all, or just call us.

Auto steer for Steiger tractors, from a Panther to a Quadtrac 620

Deep Sand Tech puts affordable FJDynamics auto steer on articulated Case IH iron of every age, from a 1970s Steiger Panther to a 9370 to an STX 450 to a Tier 4 Quadtrac, steer ready or not. A tractor that bends in the middle steers differently than a front-axle tractor, and we set the kit up for that. If it has a steering wheel and 12 volts, Deep Sand Tech has you covered!

Get a quote for your Steiger Call or Text (580) 394-0089
Any SteigerPanther, Cougar, Wildcat, 9100 to 9390, STX 275 to 535, Steiger 350 to 620, Quadtrac, Rowtrac, AFS Connect
Built for articulatedArticulated mode, hinge-pin measurement and a cold-valve tune are part of every Steiger setup
Within 1 inchRTK pass-to-pass accuracy on the same lines year after year
1-year buy backRun it a season. If it is not for you, we buy it back

Three ways we steer a Steiger

  1. Electric steering motor kit in articulated mode

    The AT2 or AT2 Max motor bolts to the steering column and turns the wheel. Nothing in the hydraulics is touched, which is why it is the first pick on a 9100 to 9390, a base STX, or any older Steiger with no steering valve. The display is switched to articulated mode so it steers from the hinge, not from a front axle. Any Steiger can run it, including guidance-ready units that already have a valve.

  2. AH2 on the factory valve

    Guidance-ready STX, Steiger 350 to 620, Quadtrac and Rowtrac tractors came with a factory steering valve. It is driven by a voltage signal, not CAN, even on units that were sold as CAN. The AH2 runs that valve with a new valve head and two plug changes, so the steering wheel stays stock and the motor stays in the box. Tracks included.

  3. AH2 with a valve added

    If you want hydraulic steering on a Steiger that never had a valve, we add one and run the AH2 on it. More install than the motor kit, so we only steer you this way if there is a reason for it, like a cab you share with a lot of operators.


Case IH Steiger and Quadtrac model families and what fits

What each family came with from the factory, and what we usually put on it. A family being listed means the option existed, not that every tractor has it, so we confirm on your unit before anything ships.

Model familyFrom the factoryWhat we usually install
Steiger Panther, Cougar, Wildcat, Bearcat
1970s and 1980s, before the Case IH 9100 series
No steering valve. Power steering only.Electric motor kit in articulated mode. Steigers normally take a 19 or a 6 tooth spline. Some have a keyway hub with no teeth, and the 1976 Wildcat ST210 has a cone-wedge hub with a key, so we match the adapter from a photo first.
Case IH 9100, 9200 and 9300 series Steiger
9110 to 9180, 9210 to 9390
No steering valve from the factory.Electric motor kit in articulated mode, or AH2 with a valve added.
STX base models
STX 275, 280, 325, 330, 335, 375, 380, 385, 425, 430, 435, 440, 450, 480, 485, 500, 530, 535
No steering valve unless a dealer added guidance.Electric motor kit in articulated mode, or AH2 with a valve added. Many used STX tractors had guidance added later, so a photo of the valve area settles it.
STX guidance-ready and Quadtrac
Same STX models with the guidance-ready option or Autosense, wheeled or Quadtrac
Factory Eaton valve driven by a voltage signal. Not CAN.AH2 on the factory valve with a new valve head and two plug changes. Motor kit also fits if you would rather not touch the valve.
Steiger Tier 4 and 4b, Quadtrac, Rowtrac
350, 370, 400, 420, 450, 470, 500, 540, 550, 580, 600, 620, about 2011 to 2019
Factory Eaton valve on guidance-ready units, driven by a voltage signal. Some 2016 and newer 420 to 620 frames carry a Danfoss valve instead. Some were sold as CAN steer.AH2 on the factory valve with a new valve head. We check the valve tag before the head ships. Motor kit on units with no valve.
AFS Connect Steiger
370, 420, 470, 500, 540, 580, 620, 2020 and newer, wheeled, Quadtrac and Rowtrac
CAN steering from the factory, but not on FJD’s approved CAN list yet.AH2 on the valve with a new head, or the electric motor kit in articulated mode.

Looking for one model number? Steiger, STX and Quadtrac lines are in the Case IH steer-ready model list under articulated 4WD tractors.

Not on the list, or a different brand wearing the same model number? Call us. If you can send a photo of the steering valve, or tell us there is not one, we can usually name the kit from that.


See the AT2 motor kit

The same motor kit we put on Steigers, shown on a front-axle tractor. The bracket and spline change, the kit does not. One minute and eighteen seconds.

Deep Sand Technology's AT2 Autosteering System by Fjdynamics

What goes on the tractor

FJD AT2 electric steering motor mounted on a tractor steering column
The motor bolts to the steering column and turns the wheel. Nothing in the hydraulics is touched.
FJD GNSS receiver mounted on a tractor roof
The GNSS receiver goes on the roof and takes the RTK correction over cellular or radio.

Things we have learned on Steiger installs

  • On an articulated tractor the receiver-to-axle measurement in the vehicle setup is really receiver to hinge pin. Measure to the pin, not the rear axle, and do not double it.
  • Mount the GNSS receiver toward the front of the cab roof, not over the hinge. The closer the globe sits to the hinge, the touchier the steering gets, and the measurement to the pin has to be a tape measure, not a guess.
  • Our usual articulated starting point on the motor kit is Model 2 with no wheel angle sensor, speed ratio 24, Ultra Low Speed on, control deadband 4, max rotation 50, RPM deadband 1. Then we tune it live with you on the phone, because every Steiger is a little different.
  • On guidance-ready Steigers the CAN connectors are on the left side under the buddy seat, behind the toolbox. The FJD wheel angle sensor mounts in the same spot as the factory Autosense sensor, and its cable has to point straight forward, not at an angle.
  • The valve head on a guidance-ready Steiger comes off with four screws. Clean the valve with brake cleaner and air before the swap so nothing falls in. With the right tools it is a ten minute job, without them it can eat an afternoon.
  • Factory valve heads on these tractors are not temperature compensated. Steering is jerky for the first hour until the oil warms up, then it smooths out. We tune for it, and a head with wiggle in it gets replaced with the twin-coil style.
  • Steigers normally take a 19 or a 6 tooth spline, but some have a keyway hub with no teeth. We stock a few keyway adapters and have had custom splines machined when nothing in stock fit.
  • A Steiger 450 Quadtrac on the AT2 Max with the AH2 on the factory valve holds a line well enough to run land leveling.
What to send us for a quote
  • Model and year, and whether it is wheeled, Quadtrac or Rowtrac.
  • A photo of the steering column from the seat, so we match the bracket and spline. On a Panther or Cougar, a photo of the hub with the wheel off if you can.
  • Whether a dealer ever put guidance on it, and a photo of the steering valve if there is one. The valve tag tells us Eaton or Danfoss.
  • A photo of the connectors under the buddy seat on a guidance-ready unit.
  • What you pull with it and how fast, so we set the articulated tune for the job.
Talk to farm experts

Common questions from Steiger owners

Will auto steer work on a Steiger?

Yes. Any Steiger from a 1970s Panther to a 2020 AFS Connect Quadtrac can run FJD auto steer. Tractors with no steering valve take the electric motor kit in articulated mode. Guidance-ready STX and Steiger 350 to 620 units take the AH2 on the factory valve with a new valve head. Either way it holds within an inch on RTK.

My Steiger is guidance-ready. Does the AS2 plug in?

No. Steigers and STX tractors drive the steering valve with a voltage signal, not CAN, even when they are advertised as CAN. We run the AH2 on the factory valve with a new valve head and two plug changes. It is a repeatable job and works on Quadtracs.

What about a 2020 or newer AFS Connect Steiger?

Those have CAN steering from the factory, but they are not on FJD’s approved CAN list yet. We run the AH2 on the valve with a new head, or the electric motor kit in articulated mode. Call us with the serial number and we will tell you where the list stands.

Does auto steer work on a Quadtrac or Rowtrac?

Yes. Tracks steer the same way as wheels on a Steiger, from the hinge. Guidance-ready Quadtracs take the AH2 on the factory valve. Base units take the motor kit. A Steiger 450 Quadtrac runs land leveling on the AT2 Max.

What does articulated mode change?

The display steers from the hinge instead of a front axle. The vehicle measurements are taken to the hinge pin, the receiver mounts toward the front of the cab, and the tuning numbers are different. We set it up with you on the phone the first time it goes to the field.

Will a motor kit fit the spline on an old Steiger?

Usually. Most Steigers are a 19 or a 6 tooth spline, which we stock. Some have a keyway hub with no teeth, and a 1976 Wildcat ST210 has a cone-wedge hub with a key. Send a photo of the hub before you order and we match the adapter, or have one machined.

Why is the steering rough when I first start up?

The factory valve heads on guidance-ready Steigers are not temperature compensated. For the first hour the oil is cold and the steering is jerky, then it smooths out. We tune for it. If a head has wiggle in it, it gets replaced.

Do I lose my factory display or guidance?

No. The FJD kit runs on its own display and its own receiver. The factory screen stays put and still does what it did before.


Other tractor brands

Same approach, different color of paint. Pick a brand for its model-by-model fit.

More on auto steer

Auto steer for tractors · How auto steer works · Is my tractor steer-ready? · Auto steer for older tractors · Hydraulic auto steer (AH2) · AS2 steer-ready · Compare FJD auto steer systems · Tractor GPS systems · RTK vs WAAS · FJD AT2 vs Wheelman · FJD AT2 vs Trimble EZ-Steer · All buyer guides · Autosteer solutions across the United States

Deep Sand Technology

About Deep Sand Technology

Deep Sand Technology (Deep Sand Tech) is a farmer-owned, authorized FJDynamics dealer with over 30 years of experience. We sell, ship, install and support FJD autosteer kits and GEODNET network RTK for thousands of farmers across the US, in all 50 states. Everything on this page comes from our own installs and support calls, not from a brochure.

About us · Farmer reviews · Talk to a farmer · Call or text (580) 394-0089

It's easy to get started. Talk to a farmer today.

By submitting this form you agree to our Privacy Policy.