Auto steer for Versatile tractors, any model, any year
Deep Sand Tech puts affordable FJDynamics auto steer on Versatile tractors of every age, from a Ford Versatile 846 or a 2375 to a new 610 Deltatrack, steer ready or not. If it has a steering wheel and power steering, Deep Sand Tech has you covered! Every system comes with sub-inch RTK accuracy unlocked, a two-year warranty, fast phone and remote-login support, and a 1-year buy back guarantee.
Get a quote for your Versatile Call or Text (580) 394-0089Three ways we steer a Versatile
Electric motor kit on the column
AT2 Lite, AT2, AT2 Max or AT2 Ultra. A motor and a model-specific bracket bolt to the steering column and turn the wheel. Fits any Versatile with a steering wheel. This is what goes on the Ford Versatile 846 to 976 and 9x80 series, the 2290 to 2425, the Genesis 2145 to 2210 and every base-model 4WD. Articulated tractors run in articulated mode with their own settings. Most farmers install it themselves in an afternoon.
AH2 on the factory valve
Auto-Guide-ready Versatiles carry a hydraulic steering valve that is driven by a voltage signal, not CAN. AH2 runs that valve. We change the valve head and two plugs, add our own round angle sensor, and the factory valve does the steering. Nothing from the factory gets thrown away.
AH2 with a valve we add
A base-model Versatile has no valve. If you want hydraulic steering instead of a motor on the wheel, we add a valve and run the AH2 on it. Any tractor with power steering can run a hydraulic kit. We tell you which way makes sense after we see the model and year.
Versatile model families and what fits
What each family came with from the factory, and what we usually put on it. A family being listed means the option existed, not that every tractor has it, so we confirm on your unit before anything ships.
| Model family | From the factory | What we usually install |
|---|---|---|
| Ford Versatile 4WD, 1970s to 1990s 846, 876, 946, 976, 836, 856, 936, 956, 1156 | No steering valve. Power steering only. | Electric motor kit in articulated mode. Send a photo of the column so we match the spline before it ships. |
| Ford New Holland 9x80 and 9x84 series 9184, 9280, 9282, 9384, 9480 to 9484, 9680 to 9684, 9880 to 9884 | No steering valve. | Electric motor kit in articulated mode. A 9680 takes the number 4 spline and bracket. |
| Versatile 2290 to 2425 and Genesis 2290, 2335, 2360, 2375, 2425, 2145 to 2210 | No steering valve. A 2335 with a Raven PWM valve block is the exception. | Motor kit. A 2375 Classic shares its column with the New Holland Genesis: trim the plastic, number 6 bracket, 4J spline. A Raven PWM block on a 2335 runs on the AH2. |
| Versatile 305 to 575 4WD, base model 305, 340, 350, 375, 400, 435, 450, 485, 500, 535, 550, 575 | No steering valve. | Electric motor kit in articulated mode, or AH2 with a valve we add. |
| Versatile 350 to 610 4WD and Deltatrack, Auto-Guide ready 350, 375, 380, 400, 405, 430, 450, 460, 500, 520, 550, 570, 610 | Factory hydraulic valve driven by a voltage signal. Not CAN, even when it was sold as steer ready. | AH2 on the factory valve with a new valve head, two plugs and our round angle sensor. Deltatracks included. |
| Versatile 190 to 365 row crop 190, 220, 250, 280, 305, 260, 265, 290, 295, 310, 315, 335, 365 | Base models have no valve. Auto-Guide-ready units carry a factory valve. SuperSteer units we verify on the tractor. | Motor kit on base models. AH2 on the factory valve on guidance-ready units. |
| Versatile Nemesis 175, 195, 210 | Auto-Guide-ready units carry a factory valve. | AH2 on the factory valve, or the motor kit. |
Not on the list, or a different brand wearing the same model number? Call us. We have put kits on Versatile 856s and 375s.
See the AT2 motor kit
The same kit that goes on a Versatile. One minute and eighteen seconds.
What goes on the tractor


Things we have learned on Versatile installs
- Versatile steer-ready is not CAN. The factory valve is driven by a voltage signal, so an AS2 kit will not steer it. Another dealer sold an AS2 for one and spent two days with the roof off. We send the AH2 with a round angle sensor from the start.
- The hydraulic harness on a Versatile needs its resistor. Leave it out and the tractor steers one direction only.
- On a Versatile 4WD the valve sits at the hinge, opposite the door side, at chest height. Easier to reach than on most articulated tractors. Changing the valve head is four screws.
- Versatile uses a green 12-pin plug that is keyed. Some aftermarket plugs are not keyed and fit both ways. One way works, the other shorts the controller. We match the keyed plug.
- On a Versatile you can run the factory pressure sensor or FJD’s own. After the valve head change, the factory autosteer gets disabled so it does not throw codes.
- Versatile 365, 375, 850 and 856 articulated tractors need the articulating vehicle profile. On an 856 that was oscillating, Model 2 with online aggressiveness 1.2 settled it. Most Versatiles run with no wheel angle sensor on the motor kit.
- A 2375 Classic, a New Holland Genesis and a Rogator share the same steering column. Take the plastic off around the turn signal, trim it, and the number 6 bracket clamps on the metal.
- To get the steering wheel off a 280-style column, a 7/16 deep socket over the lock threads and a tap with a hammer pops it.
- Model and year, and whether it is articulated, Deltatrack or row crop.
- A photo of the steering column from the seat, so we match the bracket and spline.
- On a 4WD, a photo of the valve at the hinge, opposite the door, and whether the tractor was sold Auto-Guide ready.
- Any implement you want rate or section control on, and which display is already in the cab.
Common questions from Versatile owners
My Versatile is steer ready. Is it plug and play?
Close, but not the way a CAN tractor is. Versatile steer-ready drives the valve with a voltage signal, not CAN, so the AS2 kit does not fit it. The AH2 does. We change the valve head and two plugs, add our round angle sensor, and the factory valve steers. We walk you through it on the phone.
Will auto steer work on an old Ford Versatile 846 or 876?
Yes. The motor kit bolts to the column and runs in articulated mode. Send us a photo of the column and we match the spline and bracket before it ships.
Do I need a wheel angle sensor on an articulated Versatile?
On the motor kit, usually not. Most of our articulated customers run with no angle sensor and a speed ratio we set with you on the phone. On the AH2 hydraulic kit we add our round angle sensor.
What about a Deltatrack?
Same as the wheeled 4WD of the same year. Auto-Guide-ready Deltatracks carry the factory valve and take the AH2 with a new valve head. Base models take the motor kit or AH2 with a valve we add.
Can it steer my 2375 or Genesis?
Yes, with the motor kit. The 2375 Classic and the Genesis share a column with the Rogator: trim the plastic around the turn signal and the number 6 bracket clamps to the metal with a 4J spline.
Do I need my own base station?
Usually not. Every kit ships with an RTK plan, and most customers run on the GEODNET network, which needs no base station of your own. Where coverage is thin we set you up with a base station or StarNav. We check coverage at your farm before we quote.
Who installs it and who do I call?
Most farmers install the motor kit themselves in an afternoon with our tech on the phone. A valve-head change on a steer-ready 4WD takes longer and we walk you through it. After that you call or text Deep Sand Tech, and we can log into the display remotely to help.
Other tractor brands
Same approach, different color of paint. Pick a brand for its model-by-model fit.
More on auto steer
Auto steer for tractors · How auto steer works · Is my tractor steer-ready? · Autosteer for older tractors · Hydraulic auto steer (AH2) · AS2 steer-ready · All autosteer kits · RTK vs WAAS · FJD AT2 vs Wheelman · All buyer guides · Autosteer solutions across the United States

